Your camper sits in winter storage for a few weeks or months, and all the electrical devices are (supposedly) switched off. Yet when you next start up, the onboard battery barely shows any voltage, and not even the heater will ignite. In the worst case, the battery is deep-discharged, meaning so empty that it's been damaged.
This is rarely caused by a major fault. Usually it's small, constant power drains that quietly pull a few milliamps around the clock. We'll show you what these can be, how to prevent deep discharge, and how you might still rescue a drained battery.
Contents
Our own mishap: the router drained our battery dry
Even our own onboard battery, a classic Optima with 75 Ah, once fell victim to an undetected power drain and ended up deep-discharged after one of our last winter breaks. The culprit: our CamperNet, a permanently installed internet router hidden away in a cupboard.
Tracking down the fault took forever, but ever since that incident, we've made a habit of disconnecting the battery whenever the camper sits unused for longer periods. These days, we even do this when there's just a longer gap between two summer trips.
A glance at the datasheet shows how much chaos a small router can cause: manufacturer Antretter & Huber states a typical power consumption of 340 milliamps (mA) for the CamperNet Pro 5G. The CamperNet EVO 5G-ready draws 320 mA, according to the manufacturer.
It's like a dripping tap. A single drop goes unnoticed, but after a month the bucket is full anyway. According to the manufacturer, the CamperNet Pro 5G warns with a flashing red status light once voltage drops below 11.5 volts, except nobody sees that in a parked-up camper.
According to the datasheet, the router also has undervoltage protection. However, the manufacturer doesn't specify at what voltage it kicks in.
You'll find everything about mobile internet in your camper in our guide to routers, antennas and complete solutions, and our first experiences in the article Internet on the road with the CamperNet.
The usual suspects: how much they really draw
Solar charge controller: never fully off, even at night
An MPPT solar charge controller (MPPT stands for Maximum Power Point Tracking) extracts maximum output from your solar panel. To do this, it constantly adjusts voltage and current to the optimal operating point. But its electronics need some power even without sunshine, and that comes from your onboard battery.
Victron Energy states a self-consumption of 30 mA at 12 volts for the SmartSolar MPPT 100/30. That's around 0.7 amp-hours (Ah) per day, or about 65 Ah over a three-month winter. For a small battery, that adds up to quite a lot.
If your camper is parked in a dark garage or barn, disconnect the controller from the battery. Follow the sequence specified in your controller's manual. We explain how a solar system is set up in our installation guide for solar panels on a motorhome.
If your camper is parked outside in the sun, the solar system can keep a lead-acid battery fully charged throughout the storage period. For lithium batteries, this only applies if the controller or battery management system blocks charging during frost. More on that below.

Inverter: the biggest power drain
An inverter turns the battery's 12 volts into 230 volts for your sockets. Leave it switched on, and it draws power even with nothing plugged in. The datasheet calls this value "zero-load power".
For the Victron Phoenix 12/500, the manufacturer states 6 watts. At 12 volts, that works out to roughly 12 Ah per day, or about 84 Ah per week. Rule of thumb: every watt of continuous draw costs you close to 2 Ah a day on a 12-volt system.
Many devices have a power-saving mode. On the Phoenix it's called ECO mode, and according to Victron it cuts idle consumption to 1 watt. But if you don't need 230-volt power while parked up, fully off is still the better choice.

Router and modem
An LTE or 5G router constantly holds the connection to the mobile network. Depending on the model, that costs around 8 Ah a day, as our calculation above shows. A passive outdoor antenna doesn't draw power itself, but active antennas with a built-in amplifier do.
The small drains nobody has on their radar
Besides the three big power hogs, there are plenty of mini-consumers: alarm systems, relays, and the backflow current from chargers and charge controllers. Depending on your setup, you can add gas detectors, the radio, a GPS tracker, or the electronics in your heater and fridge.
A special case is the battery monitor. Victron points out, for example, that a battery monitor connected directly to the battery can fully drain it. The battery management system (BMS) of a lithium battery also draws power: if the BMS doesn't go to sleep properly, it can draw up to 200 mA, according to the trade magazine Boote.
How to track down hidden power drains
If your battery runs flat while parked, there's no way around measuring. That sounds more technical than it is. Switch everything off as you would for a normal stay, then wait a bit, since some electronics take time to enter standby mode.
A ADAC quiescent-current test with 25 vehicles shows just how long that can take. There, it took around 25 minutes after locking up before the vehicles had powered down their consumers enough that only 5 to 40 milliamps were still flowing.
Read the battery monitor. If you have a battery monitor with a shunt, i.e. a measuring resistor in the negative cable, it shows the current draw directly. If it still reads more than a few milliamps with the camper switched off, something's still running.
Use a clamp meter. Simply clamp a current clamp meter around the battery's negative cable. Just make sure it can measure direct current (DC).
Wire a multimeter in series. Disconnect the negative cable and connect the multimeter in between, set to the amp range. Don't switch on any big consumers while doing this — the measuring input is usually only fused up to 10 amps.
Pull fuses one by one. While measuring, pull one fuse after another. If the current drops noticeably, you've found the circuit with the culprit.
Don't forget the main switch. Some devices are wired directly to the battery, bypassing the main switch. That can include solar charge controllers, inverters, or a battery monitor.
If you're unsure about the electrics, better let a specialist workshop do the measuring.
We cover the basics in Motorhome electrics for beginners and Power in motorhomes and caravans: the basics.
You can read how to calculate your total consumption in Power consumption and saving power in a motorhome.
Our routine before every extended layup
- Charge the battery fully. Lead batteries (wet, AGM, gel) should always go into storage fully charged. For lithium batteries, follow the charge level the manufacturer specifies for storage. The easiest way to charge is via mains hookup.
- Switch off the inverter — don't just unplug the connected devices!
- Cut power to the router and modem Unplug the devices completely if you don't need internet during the layup.
- Disconnect the solar charge controller The same applies here: put the controller "out of action" so it doesn't keep quietly drawing power.
- Switch off the fridge An empty fridge while parked up is a waste of energy anyway.
- Disconnect the battery The ADAC recommends disconnecting the negative terminal first, and reconnecting it last when hooking the battery back up. Alternatively, you can isolate the battery with a battery disconnect switch or pull the main fuse.
- Check and recharge regularly Starter batteries should be externally recharged about once or twice a quarter during long layups. For lithium batteries, most manufacturers recommend recharging after three months at the latest.
Treat the base vehicle's starter battery according to the owner's manual. It tells you whether and how you're allowed to disconnect it on your particular vehicle.
You'll find the full list for winterizing in our winterizing checklist. In spring, our spring check with free checklist will help you out. If you're out and about in winter, check out our guide to winter camping.
Lithium batteries and frost
A LiFePO4 battery (lithium iron phosphate, the common lithium type used in campers) handles cold storage well. When charging, though, it's a different story. Victron only allows charging its Lithium Battery Smart between 5 and 50 °C, while Liontron specifies 0 to 45 °C for its LX series.
According to the manufacturer, the Liontron battery can be stored at −40 to +60 °C. If it's charged below the charging limit, the cells can suffer permanent damage. A good BMS blocks charging automatically in that case — whether your battery can do this is explained in the manual.
Find out which battery suits your camper in our guide The right leisure battery for your motorhome.
Deep-discharged battery: can it still be saved?
If it's already happened, act fast. The longer a battery sits empty, the worse the damage gets. Whether it's worth saving mainly depends on the battery type.
Measure first: how empty is the battery really?
Measure the resting voltage with a multimeter directly at the terminals. The battery should have sat without load or charge for a few hours beforehand. The ADAC (German automobile association) classifies the values for 12-volt lead batteries like this:
State of charge | conventional lead-acid battery | AGM battery |
|---|---|---|
100% | 12.70 V | 12.90 V |
80% | 12.50 V | 12.65 V |
50% | 12.20 V | 12.25 V |
20% | 11.80 V | 11.80 V |
0–10% | 10.50 V | 10.50 V |
Source: ADAC, "Testing a car battery". These values apply to starter batteries and serve as a rough guide for leisure batteries. The ADAC doesn't publish separate figures for gel batteries.
With lithium batteries, voltage tells you almost nothing about the state of charge. If it reads close to zero volts at the terminals, that's usually just the BMS having shut down.
Saving lead-acid, AGM, and gel batteries
Lead-acid batteries mainly suffer from sulfation. Crystals form on the lead plates that no longer dissolve during normal charging. The trade magazine promobil puts it this way: if a lead battery stays partially discharged for too long, the sulfate layer crystallizes and no longer dissolves when charging.
Visual inspection. If the case is swollen, cracked, or leaking acid, stop charging immediately. The battery needs to be disposed of.
Never charge a frozen battery. According to a fact sheet from the battery trade association within the German Electrical and Electronic Manufacturers' Association (ZVEI), a fully discharged lead battery already freezes at 0 °C, while a fully charged one only freezes at around −70 °C. Let it thaw to room temperature first.
Check the acid level (wet batteries only). If your battery has screw caps, check the acid level. If liquid is missing, top it up with distilled water following the manufacturer's instructions — AGM and gel batteries stay sealed and don't need this.
Choose the right charger. Many basic chargers simply won't start at very low voltage. Charger manufacturer CTEK, for example, states that most of its 12-volt chargers can charge batteries from as low as 2 volts.
Charge slowly and patiently. The charging program has to match the battery type. An ADAC example illustrates the timing: an empty 100 Ah battery can take up to eleven hours to reach 80 percent on a 7 A charger.
Reconditioning only for wet batteries. Some chargers offer a recond, regeneration, or pulse function. CTEK only approves its Recond function for wet batteries, including EFB, not for AGM, gel, or lithium batteries. According to CTEK, this step takes an extra half hour to four hours and should run no more than once or twice a year.
Make sure there's ventilation. A lead battery can release explosive gases while charging, and even more so during reconditioning. So charge it in a well-ventilated spot, away from sparks or open flames.
Check the result. Let the battery rest for a few hours after charging, then measure again. If the voltage quickly drops below 12 volts again, the battery is usually no longer usable.
If the voltage stays stuck around 10.5 volts despite charging, that often points to a shorted cell. In that case, one of the six cells is short-circuited, and the battery can't be saved.
Victron Energy says its gel and AGM batteries recover well even after extended deep discharge. However, Victron notes that frequent, prolonged deep discharges cause irreversible damage even to these types. A saved battery therefore usually ends up with less capacity than before.
Voltage alone doesn't tell you how much power a battery can still deliver. The ADAC points out that the condition of an older battery can't be judged from resting voltage alone. A specialist workshop can test it with a load test.

Saving LiFePO4 batteries
With lithium batteries, the BMS protects the cells. If the voltage drops too far, it shuts the battery down, making it appear dead. Often the cells are still fine, and the BMS just needs to be "woken up."
Check the manual first. Every manufacturer handles wake-up differently. Some batteries have a dedicated switch or an app function for this.
Connect a charger with a lithium profile.Battery manufacturer Ective explains that a charger with a LiFePO4 charging curve can wake up a locked BMS. According to Ective, this can take up to five minutes.
Charge boosters only with approval.A charge booster (a DC-DC charger that charges from the alternator while driving) with a lithium program works if the battery manufacturer allows it.
Watch the temperature.Below 0 to 5°C, depending on the manufacturer, the battery won't accept a charge. Bring it somewhere warm first.
Charge it fully right away.Victron recommends keeping the time spent in a deeply discharged state as short as possible. After waking the battery up, charge it fully.
No lead-acid programs.Recond mode, desulfation, and lead-acid charging profiles have no place on a lithium battery. CTEK explicitly excludes lithium batteries from its Recond function.
Stay away from DIY fixes.There are tips online about jump-starting lithium batteries with a second battery or a power supply. We advise against this — that's a job for the manufacturer or a specialist workshop.
If the voltage has dropped very low, Victron describes a special, slow charging procedure. It only applies to individual batteries and requires someone to supervise. If the battery gets hot or starts to bulge, stop immediately.
Victron also warns: charging a lithium battery after it's been discharged too deeply can release harmful gases. So get in touch with the manufacturer or dealer before attempting any rescue.

When a battery can no longer be saved
The case is swollen, cracked, or leaking.
The battery gets hot, hisses, or gives off a sharp smell while charging.
For lead-acid: the voltage quickly drops back below 12 volts after charging.
For lead-acid: the voltage stays stuck around 10.5 volts despite charging.
For lithium: the BMS won't wake up even with the right charger.
In that case, the battery belongs at a dealer or recycling center, not in the household trash.
Our tutorial shows you how to get a car with a dead starter battery running again: Dead car battery: here's how jump-starting works.
When you need a workshop
If the voltage drops noticeably within a few days despite all consumers being disconnected, there's likely a real defect behind it. That could be a bad cell or a short circuit in the wiring. Have a specialist workshop check it out.
Work on gas, electrical, and brake systems can be safety-relevant and subject to inspection requirements. When in doubt, hire a specialist company.
Häufige Fragen
How much power does an inverter draw at idle?
You'll find this in the datasheet as the no-load power. For the Victron Phoenix 12/500, the manufacturer states 6 watts, which works out to about 12 Ah per day at 12 volts. In ECO mode, this drops to 1 watt.
Do I need to switch off the router while the camper is parked?
Yes, if you don't need internet access. A 5G router like the CamperNet Pro 5G typically draws 340 mA according to the manufacturer, which adds up to about 8 Ah per day.
What happens if the solar charge controller stays connected?
Without sunlight, it still draws a bit of power from the battery itself — around 30 mA for the Victron SmartSolar MPPT 100/30. Over three months, that adds up to roughly 65 Ah. If your camper is parked somewhere dark, it's better to disconnect the controller.
How do I store a LiFePO4 battery over winter?
At the charge level the manufacturer recommends for storage, and disconnected from all consumers. Never store it empty, and only charge it above the minimum temperature listed in the manual, usually 0 to 5°C.
Can I still save a deeply discharged battery?
With lead-acid batteries, often yes, with the right charger and a lot of patience. With lithium batteries, usually all it takes is waking up the BMS, ideally with a charger that has a lithium profile. If the case is damaged or the battery gets hot, it's done for.


0 Kommentare
Noch keine Kommentare — sei die/der Erste und teile deine Erfahrung!
Danke!
Dein Kommentar wartet auf Freischaltung und erscheint, sobald er moderiert wurde.